Airline 7" Portable TV

One of the first things I bought off eBay, back in 2003, was this Montogomery Ward Airline 7" TV, model 84GE-3011A. It is just a rebadge of the well known Sentinel 400TV, sold by the Montgomery Ward chain of stores. Airline was their in house brand.


From left to right the controls are: Contrast, Channel, Brightness and On/Off Volume.

Background to Electrostatically deflected TV sets.
I'd always wanted a commercially made electrostatically deflected TV set, having built the Radio Television & Hobbies 5" 5BP1 TV set back in the mid 1980's. The advantages of electrostatic deflection are many, including simple resistance coupled deflection circuits and low power consumption. No weird deflection yokes and line output transformers to cause problems when they fail. It is thus easy to build a complete TV set with no hard to get parts as I found with the 5BP1 set.
In the U.S where TV had been going alot longer than in Australia, electrostatically deflected sets had existed since the start of electronic TV there. Indeed, the 5BP1 and 5BP4 tubes which appeared in 1939 were designed for the new television service. These were used in various commercially made and kitset receivers such as those produced by RCA (TRK5), Andrea, Transvision, Meissner, etc. Smaller sets were made with 3" tubes such as 3KP1 and 3KP4. The well known Pilot TV37 portable is one such example. However, post war the most popular screen size for electrostatic sets was 7", using a 7JP4 or 7EP4. At the height of popularity in the late 1940's, there were numerous table, and suitcase or oscilloscope shaped portables with a 7" electrostatic tube. The well known examples include Hallicrafters T54, Tele Tone TV149, Motorola VT71, and the Sentinel 400TV which is the set to be described here. By this time in history, 7" electrostatic sets were intended as a cheap second or portable set as the size of electromagnetically deflected tubes was now up to 16" and was preferable for the main set in the house.
In Australia, television started in 1956 and by this time electrostatically deflected sets were obsolete. Here, we started with 17" and 21" electromagnetically deflected picture tubes. However, due to the high cost of TV sets, it was common for enthusiasts to build up sets using 5BP1 or VCR97 CRT's which were plentiful on the disposals market. These tubes were commonly used in wartime oscillographic equipment such as radar indicators.
With the experience I've had with my homemade 5BP1 TV set, electrostatic deflected picture tubes and associated circuits were no stranger to me.

My Sentinel 400TV.
I acquired this set around 2002 having bought it off eBay. I got it cheap as the seller had listed it in the wrong category and thus few people saw it. The title was also misspelt which prevented it being found in the search. To add to my luck, although I only paid surface mail postage, it arrived two weeks later by airmail. I have a good collection of U.S electronics magazines from the 1940's and thought I'd have a look through to see if there was any mention of this set. Sure enough, there was a whole article, complete with circuit diagram, in Radio Electronics for March 1949. That solved the problem of getting the circuit at least.
My set was in pretty good condition cosmetically. All was there except the 6AU6 video and sync separator valves. I noticed that a couple of the 6SN7's looked like they'd been replaced as they were clean and the rest of the set had the usual amount of dust on everything. Perhaps the previous owner had tried to get the set working, gave up and put it on eBay.
The set is built on two chassis with the RF chassis on the bottom of the cabinet and the picture chassis mounted on the side of the cabinet.

Design of the 400TV
First refer to the RF chassis circuit:

Circuit of the RF chassis. Nothing too unusual here.

Tuner.
Apart from some of the valve types not common in Australian TV sets, the circuit here is not vastly different to what one would see in local design.
The main difference is the tuner design. It's a Sarkes-Tarzian incremental unit. The thing to catch the eye of the Australian reader is the pentode RF amplifier and separate modulator (mixer) and oscillator valves. By the time TV arrived here, this was obsolete technology. Australian sets started off using cascode RF amplifiers using a twin triode, usually a 6CW7 or 6BQ7. And by this time there was a range of 9 pin triode pentodes for frequency conversion, such as 6BL8 and 6U8.  Note that only half the 12AT7 is used. This seems a bit wasteful as the second triode just spends its life being cathode poisoned due to no cathode current. The other valve with half a section being wasted is the 6AL5 video detector.
So confident were the designers of this set that the intercarrier sound system would eliminate critical fine tuning adjustment, there is no fine tuning control provided on the front panel.

Video IF and AGC.
Note that the video IF is lower than the standard Australian IF. The video IF strip follows conventional practice and feeds the 6AL5 which provides detected output and also simple AGC. There is no AGC delay. The AGC system is typical of cheap sets and suffers from being dependent on the average video signal rather than the sync pulse level. This means AGC voltage fluctuates depending on scene content. There are no adjacent channel traps. This keeps alignment and the design of the IF strip simple but can be a problem in areas where adjacent channels can be received.
The video amplifier is also conventional, though by 1956 when TV had arrived in Australia, there were pentodes specifically for video use, such as 12BY7 and 6CK6. Contrast control is by variable cathode degeneration. As the contrast rheostat is turned to maximum resistance there is considerable negative feedback and thus reduction in gain. Again, typical of cheap sets, but it is simple and does work well. The plate of the 6AU6 feeds the CRT cathode in the usual way. AC coupling is used which is nothing unusual.

Sync separator and black level control.
Following the video amplifier is also the 6AU6 sync separator.  It is very simple, relying on a sharp cutoff pentode being biassed into its non linear region (note the high value cathode resistor) and thus cutting off all the video signal except the sync pulses. Despite the simplicity, there's a novel bit of circuitry added on here. See the CRT grid connected to the 6AU6 cathode? It's used as a crude form of DC restoration for the picture tube. Details were described in Radio & Television News, March 1949 p 72. If the CRT grid was earthed, the video stage and CRT would function like any other AC coupled set where the average picture brightness is always the same, regardless of scene content. However, it so happens that the sync separator cathode voltage increases with an increase in video signal. So, as scene brightness goes up, so does the voltage on the 7JP4 grid, and vice versa. Therefore, the picture will darken with a night scene for example, rather than remaining at a fixed grey level. It is not true DC restoration, but more of an automatic black level control that gives a similar effect. Not a bad compromise either, as I found once the set was working. True DC restoration restores correct black level on a line by line basis. It requires an extra diode (why didn't they use the other half of the 6AL5?) or DC coupling from the video detector right through to the CRT.

RF chassis. Note the tuner having three valves. The middle row of valves includes the video IF, detector, amplifier and sync separator. The bottom row has the sound IF, detection and output valves.

The sound and power supply stages.
The sound stage is conventional but the 6SQ7, 6AS5, and half wave selenium rectifier powering it would attract the attention of the Aussie TV technician.
Intercarrier sound is used, and this was among the first generation of American sets to do so. The 6SQ7 is a bit out of place amongst the other modern seven and nine pin valves on the chassis. The 6AT6 could have been used. Still, lots of octal valves look nice in a TV set so I'm not complaining.
The 6AS5 is a valve very uncommon here. It's one of those 2W audio output pentodes meant for 120V screen and plate operation, so common in U.S TV sets. Here the valve is run off a 130V supply from a half wave selenium rectifier fed by the 115V secondary on the power transformer. Normal practice using this type of valve is where the B+ is 250V and the audio and IF stages are in series with each other in terms of DC supply.
The power supply uses a transformer with the usual 6.3V heater windings, and a 115V secondary for B+ . This is also typical of Australian practice, except for the rectifiers. Where an Australian TV power transformer has a 115V secondary, it is fed into a full wave voltage doubler to provide 250V DC.
The Sentinel approach is to use a half wave rectifier to provide 130V for the audio and sync circuits, and a half wave voltage doubler to provide 260V for the deflection circuits. The asymmetrical loading of the transformer certainly won't contribute to efficiency with some core saturation and heating resulting.
They could have used a full wave doubler with the same number of components. The set has no fuse. Not something I'm thrilled about. Provided there's no shorts in the transformer itself or the heater line, the 10R and 33R resistors feeding the rectifiers will act as fuses.
Now to the interesting part; the picture chassis:


Typical of electrostatic deflection circuitry, this is the circuit of the picture chassis. Note the simplicity compared to a set using electromagnetic deflection.

EHT RF power supply.
To the average Aussie tech brought up on nothing but small variations of electromagnetically deflected TV sets, this part will seem quite unusual.
First, note how simple it is. No vertical output transformer to go o/c, no line output transformer or yoke to develop shorted turns and require exact replacements. Starting with the 7JP4 picture tube, it is like any other oscilloscope tube except it's larger and has white (P4) phosphor. EHT is around 5KV. The EHT comes from an RF oscillator type power supply. While earlier sets used a high voltage transformer operating at mains frequency feeding a 2X2 or similar rectifier, there were disadvantages with this scheme, especially as EHT requirements increased over the years. With the usual turns per volt ratio used with iron cored transformers operating at 50 or 60 cycle  mains frequency, many thousands of turns of very fine wire are required. Not only is this fine wire prone to breaking, but keeping it insulated from the other windings and the transformer core is a problem. There is also a safety issue. Such a power supply can easily provide enough current to kill. Further, DC filtering requires high value paper capacitors because of the low frequency, and invariable half wave rectification used. The high capacitance not only makes for expensive capacitors, but also adds to the shock hazard.
By the mid 1940's RF power supplies had become a popular way to obtain the EHT. Running at high frequency means a small air cored transformer with fewer turns is required. The high frequency also allows low value filtering condensers to be used. In this set they're only 350uuF. And, the regulation is such that the voltage will drop considerably if someone gets across the EHT. Typically, a high power audio pentode or beam tetrode is used in a self oscillating circuit. Typical valves used are 807, 6L6, 6V6, or as used here, 6Y6. Positive feedback is obtained from a winding on the transformer, or sometimes by a low value of capacitance to the EHT winding as is the case here. You don't see the capacitor? It's there in the form of a ring clipped around the glass of the 1B3 EHT rectifier. The plate of the 1B3 is the other side of the capacitor with the glass being the dielectric. Feedback, and thus output voltage can be adjusted by the position of the "OFR" (Oscillator Feedback Ring). The 1B3 heater is fed off a separate winding on the RF transformer as it's directly heated with the cathode floating at 5KV. This is the same as with a conventional line output transformer.
In this set there's also a second supply, of about 760V produced. This comes from another secondary which feeds a 6X5. Again, note the low values of filter capacitance. The 6X5 heater is fed of an isolated winding on the mains transformer so as not to stress the heater to cathode insulation. In fact there's a 2.2M resistor from heater to cathode to keep both at the same potential. This 760V feeds the horizontal deflection output and oscillator.
The RF power supply is powered from the 260V supply.
Across the 5KV supply is a voltage divider made of high value resistors and preset pots. This supplies the DC for the deflection plates to ensure the picture is centred on the screen, and the screen and focus grid for the 7JP4. The bottom end of this voltage divider feeds the vertical output stage at 700V. The horizontal output, although using a similar voltage, cannot be fed from this point as it requires more current than flows through the voltage divider.

Top view of the picture chassis. The RF power supply is in the shielded box, to the left of which is the 6Y6. The 6SN7's and 6SL7 are grouped together on the other side. The 1B3 and 6X5 are inside the shielded box.

Vertical deflection.
Starting with the vertical section, a conventional 6SN7 twin triode multivibrator is used. This provides a sawtooth waveform, then amplified by a 6SL7 wired as a push pull amplifier. The vertical plates of the 7JP4 are coupled to the 6SL7 by low value 6KV condensers. Low values (i.e.. cheap, small) can be used because of the high impedance of the deflection plate circuit; the plates being voltage driven and not current driven. Note the 4.7M plate resistors of the 6SL7. Such high values are used to obtain the high voltage swing required, and to further aid this, they are fed from 700V.
Here, we can see the limitations of electrostatically deflected CRT's. As screen size goes up, so does the deflection voltage required, unless the deflection angle remains the same. However, this results in a very long tube. Larger screens require more EHT. This reduces deflection sensitivity as the electron beam becomes stiffer. DuMont was quite fond of large electrostatic tubes in their prewar sets. The largest electrostatic tube I am aware of is the 20AP4. It has a length of about 27". Needless to say, such tubes are best accomodated in "mirror in the lid" cabinets. As an example of the deflection voltage required, DuMont's prewar 14" set, using a 14AP4,  required a 1500V B+ for the deflection output valves, operating as ordinary resistance coupled amplifiers.  Despite the practical size limitation, electrostatic tubes do have advantages where only a small screen is required.

Horizontal deflection.
Turning now to the horizontal section, again a 6SN7 is connected as a multivibrator. This feeds another 6SN7 as horizontal output. Due to the higher frequency, even lower value coupling condensers can be used to feed the deflection plates.
The horizontal oscillator is triggered directly off the sync pulses. There is no AFC circuit. This is another surprise for the local technician given there were no commercially made TV sets in Australia that did this. Horizontal AFC is seen as necessary because noise pulses in the off air video are the same polarity as the sync pulses (something inherent in the negative modulation system used in Australia and the U.S). An AFC circuit used with a horizontal oscillator effectively makes the whole thing a phase locked loop. The oscillator frequency is controlled by DC, the result of which is obtained by comparing the incoming sync pulses with the frequency of the oscillator itself. The further the oscillator drifts off frequency, the greater is the DC to bring it back. The time constant of the DC filter is the key to the noise immunity. By having it longer than the period of a few lines, high frequency noise is ignored. For small screen cheap sets, AFC was ignored. In reality, the signal has to be pretty noisy for lack of AFC to become evident. The small screen hides any minor noise triggering anyway.


How the two chassis are arranged in the cabinet. Rather awkward to set the CRT rotation correctly!

Restoration begins.
Having extracted the chassis, I could see that set had hardly ever been serviced except for a few valve replacements, and a 1.8M resistor which had been added to the EHT divider network, presumably to compensate for other resistors going high and the serviceman being too lazy to replace them.
I noticed the 6BH6 RF amplifier valve had been replaced by a 6CB6. The channel knob was damaged from it slipping on the splines of the tight tuner shaft but looked repairable. And so begun the tedium of desoldering and unpicking numerous paper condensers. I found virtually all the resistors, while a bit high in some cases, were not so far out as to be worth replacing. A later 7" set I restored (Admiral 17T1) also seemed to have all its resistors close to value. It seems American resistors of the period must be quite stable, unlike the IRC horrors filling the underneath of Australian radio and TV sets.
I also had to replace the rubber flex that ran between the mains input socket and the switch as it was hard and crumbly.
Most of the work in restoring a vintage TV set is in replacing condensers and resistors. Generally, I replace every resistor over 100K and every paper condenser unless it is a cathode bypass and the cathode resistor is only up to a few hundred ohms. I leave electrolytics in as I have so rarely found defective ones (in Australian sets at least). I am now replacing mica condensers in certain instances as these are now old enough to be causing intermittent faults (e.g. scratchy sound, intermittent sync) as the plate material migrates through the mica.
After all that, usually all that is required is a touch up of the presets and local oscillator cores in the tuner.

Using an American TV in Australia.
However, this being a set for the U.S standard would need more to get it working here. Put simply, to use a system M television on system B, as used in Australia, the following things need to be done. 1) provide 120V by a stepdown transformer, 2) readjust vertical hold and height to run at 50c/s, 3) retune the sound IF to 5.5Mc/s, 4) adjust local oscillator cores in tuner. The line frequencies of 15,734c/s (U.S) and 15,625 (Aus) are close enough that not even the horizontal hold needs adjustment. If the set is a colour one, it will of course work with a monochrome picture. Much more work is involved converting an NTSC colour decoder to work on PAL. I have done it once with a solid state set and it worked well. Not only does the chroma circuitry have to be retuned from 3.58Mc/s to 4.43Mc/s, but there's circuitry which has to be added to invert the phase of the red colour difference channel on every second line. The colour decoder then works in PAL-S. It is hardly worth the effort to stuff around with adding a delay line to make it work in PAL-D.

The two chassis can be run outside the cabinet, flat on the bench, as the connecting cable is just long enough. At the initial power up it was obvious this had been done before as the CRT had been rotated so the picture was the right way up with the picture chassis in this position. As you can see from how the chassis is in the cabinet, the CRT is normally turned around to a bit over 90 degrees so the picture appears correctly to the viewer. Evidently someone had played with the set since it was last used.

The connecting cable is just long enough to allow the chassis to be connected together when flat on the bench. Needless to say, this pic was taken once the set was operational, and before the CRT had been rotated to the correct position.

Initial Testing and retuning the sound IF.
Once I'd connected the aerial and plugged the set into my UTC R44 240-120V stepdown transformer, I could tune in some channels which were close enough in frequency to some of the U.S ones. Of course there was no sound due to their sound being 4.5Mc/s above the vision carrier, and ours being 5.5Mc/s. There wasn't enough adjustment in the SIF or ratio detector transformers so I had to replace their tuning capacitors with ones of lower value. The ratio detector primary had 12uuF across it, but this needed to be lowered to 6.8uuF. Likewise, the secondary needed the 82uuF replaced by 39uuF. For the SIF coil, I  removed the 3uuF capacitor and this gave enough tuning range. Strictly speaking, the video IF should be realigned to accommodate our wider video channel and to ensure the sound carrier is at the correct level for intercarrier reception, but in practice it isn't usually required.
Sensitivity and general gain of the front end seemed poor. Even with the contrast wound up the picture was still lacking in good greyscale. I couldn't find any defective components around the video IF or output so then checked the valves. Some of the 6AG5's were a bit weak, but one particularly so. I replaced it with a 6CB6 which improved things. I couldn't be bothered looking for a 6AG5 as in this circuit the difference is insignificant. Incidentally, I did try one of the 6AG5's in the tuner's RF amp just to see; it was no better than the 6CB6 which had been put there.
I found the B+ to be low. Mainly this was due to the 100uF feeding the voltage doubler being low in value, but there was a worthwhile increase when all the three selenium rectifiers were bridged with 1N4007 diodes. Selenium rectifiers are known for failing as they age so I wasn't surprised. Normally, a series resistor should be added when installing a silicon diode due to its much lower resistance, but there were already series resistors which could perform the function. The B+ was not excessively high either.

No retrace blanking.
Another annoying thing was retrace lines being visible. This set, like all the other electrostatic sets I've seen has no retrace blanking circuit. At certain brightness and contrast settings one can reduce the problem but they seldom go away completely. And, with today's field blanking interval filled with teletext and various other signals the problem is worse. With the Admiral 17T1 I'd restored, I developed a simple but effective circuit which coupled one of the 6SL7 vertical output plates into the CRT grid via a 100uuF condenser. This provided a negative pulse, cutting off the CRT during vertical retrace. It worked so well with the Admiral, I simply adapted it for the Sentinel. However, I found the blanking to be excessive, causing shading on the left side of the picture. I could have reduced the capacitor value, but instead I fed it into the grid via a voltage divider.

I noticed poor horizontal linearity on the right side of the picture. I know that these electrostatic sets because of their cheapness often don't provide linearity adjustments, especially for the horizontal, but this was not acceptable. Eventually, I found I'd connected one of the deflection plate coupling condensers to one of the 6SN7 grids rather than the plate. This sort of mistake is not uncommon due to the tedium of large scale component replacement. This fixed, I turned my attention to the vertical linearity which was really bad.

Under the picture chassis, the new 6KV blue ceramic deflection plate coupling condensers can be seen. The voltage doubling selenium rectifiers are towards the top near the front of the CRT.

Bad vertical linearity.
I spent several days on this and undoubtedly it was the most difficult part of the restoration. I just couldn't find any mistake with my wiring or high resistors. I even checked the valves. It looked like I might have to modify the circuit which I wasn't keen to do, but when everything is connected correctly, and the components are good, what can you do? I found that increasing the value of the .15uF in the vertical waveshaping circuit would improve it somewhat. In fact I had to double it to get acceptable linearity which seemed a bit excessive. Especially so, as many of these electrostatic sets don't even have a linearity control! But then I had an idea; what if it's because I'm running at a lower frame rate? It may be that with a field period of 20mS (50c/s) that the circuit couldn't cope when it had been optimised for 16.67mS (60c/s). The trusty DVX555 digital box held the answer. I set its output to NTSC and fed the test pattern in at 60c/s field rate. The linearity was much better and in fact almost passable to a non technical viewer, so it seemed my theory was confirmed and modifications were justifiable. The .15uF was changed to .33uF and at last the test pattern resembled a circle and not an egg. It still wasn't perfect and with some bottom cramping still evident, it seemed we needed more low frequency response in the vertical amplifier. I had noticed during restoration that the .1uF from pin 2 of the 6SL7 was .01uF in my set. This couples the amplified sawtooth present at pin 2 into the second triode so that an out of phase sawtooth is present at pin 5, thus creating push pull output. With a 6M series resistor I didn't think the difference between a .01uF and .1uF capacitor's reactance at 50c/s would matter, but I tried it and there was a slight but worthwhile improvement. So, I installed a .1uF as per the circuit.
The linearity was now quite passable, especially on ordinary program material. One thing very evident while running with the 60c/s field rate is how poor the power supply filtering and or magnetic radiation from the power transformer is. The picture took on a very strong 10c/s weave.
This is why the field rate of a country's TV system is the same as the mains frequency, though not locked to it.
During most of this fault finding, I'd been using my DVX555 to feed the set with the Philips PM5544 test pattern. I fed the video output straight into the 6AU6 grid after unplugging the 6AL5. It is far easier to service a set with a fixed image, and preferably one with a circle and a symmetrical grid.
Some time after restoration, I found and article in Radio Electronics from January 1951 that explained the linearity correction circuit used in this set. It seemed to imply that the .15uF should actually be about half the two .1uF's across the linearity pot. According to that, both Sentinel's and my own chosen value for that capacitor are wrong...unless it was a misprint and was meant to be the other way round. If and when I pull the chassis out again, I might just try a .047uF and see.


Some off air pictures. The 7JP4 was in good condition. Ignore the dark band; it's caused by my camera having a too fast shutter speed.

Sync separator problems.
The picture chassis was now finished with and I could attend more closely to the RF chassis with its sync and tuner problems. Sync was poor. Scene content was obviously present in the sync and so it was observable on the CRO. At medium to low contrast settings there was a severe 50c/s ripple on the sync pulses. This wasn't present in the video coming out of the 6AL5, so had to be associated with the 6AU6 video amplifier. Increasing the filtering of the B+ feeding the 6AU6 reduced it considerably. Again I had to do a mod, and permanently connect a 10uF across the existing 10uF filter condenser that feeds the 6AU6 and the front end of the set. This, despite the fact the existing 10uF electrolytic tested good, indicated inadequate filtering. True, it would have been better with the set running off 60c/s mains so I felt justified adding the extra capacitor, but shows the filtering was at its limit to start with. For good measure I added an extra 22uF across the 20uF connected to the filter choke. Now, the sync was good on the test pattern. However, once I went back to off air signals it wasn't much better, with video content still contaminating the sync pulses. I played around with the bias of the 6AU6 sync separator but this didn't achieve much. Visions of installing an LM1881 IC came into my head but that would be too drastic a modification. Surely with such a simple circuit there couldn't be much wrong. I had noticed an extra resistor on the circuit diagram not present in my set. It's the 270R between the 6AU6 cathode and the other cathode bias components. I had no idea why it was there and was sceptical of it being required. After all, with less than 1mA of plate current, 270R isn't going to do much. But I tried it anyway, and that was it! One would assume it works because there's no bypass capacitor across it and thus allows some AC feedback to stabilise the circuit. Or it could be the suppressor grid needs to be slightly more negative than the cathode.
There is still the occasional loss of vertical sync on scene changes and a little bit of horizontal instability on strong channels if the contrast is wound up too high, but it would probably have been acceptable in 1949 in a cheap portable set.
A later trawl through my early 50's electronics magazines (Radio News or Radio Electronics) had an article on the Pilot TV37. Much to my interest, this set uses the same 6AU6 sync separator/DC restorer as the Sentinel. Pilot also included the mystery 270R resistor, but their cathode bypass is only 5uF. I wonder if the shorter time constant would get rid of the corrupted sync on some scene changes. Something else to try next time I have the set apart.

Under the RF chassis. The 130V selenium rectifier is at the bottom. By 1948, prefabricated tuners had been developed and the Sarkes-Tarzian unit used here is such an example.

The tuner.
Almost there! Now for the tuner. I'd found my initial attempts at adjusting this to be way out; I'd been using one channel higher than I should have. Once I learned what each oscillator slug corresponded to what channel I could set about this in a more methodical way. It turned out that C11 was way out, allowing the local oscillator to run about 6Mc/s higher on all channels. C11 is adjusted by a screwing a slug in and out. In the version of this tuner that has user adjustable fine tuning, this capacitor would perform that function. Instead of being slug adjustable I would presume it would be spring loaded, bearing against a cam attached to the fine tuning control.
Incidentally, one can see the screw hole for where the Ch1 oscillator screw would have been. The rotary switch certainly allows for Ch1 too. Not surprising as this was not long after Ch1 had been dropped in the U.S. In fact, the Hallicrafters T54 still had the Ch1 position on its push button tuner.
Despite the crudity of the resistance coupled RF amplifier, it does contribute to the gain. Some channels can be received with no aerial, 80km from the transmitters. However, in comparison to a more modern set with a cascode TRF amplifier, it is less sensitive. The Radio Electronics review made a point of this, mentioning Sentinel claiming an indoor aerial to be useful only in optimum conditions.

Tuning for Australian channels.
Back to the tuner. Unfortunately, some of the Australian channels are halfway between the American ones and this can really test the limit of adjustment with some tuners. Luckily, although this tuner is of the incremental variety, as far as the RF circuits go, each oscillator coil is separate and functions on its own. This eliminates the problem where a single tapped oscillator coil is used and adjusting one channel throws the rest out of alignment.
Brass screws are used to adjust the local oscillator frequency. Presumably because the Q is better than if ferrite is used. Where brass is used, screwing the core in raises the frequency, whereas ferrite lowers it.
For the receivable VHF channels in the Blue Mountains, channels 2,3,7,9 and 10, I used the corresponding American channels 3, 6,8,10 and 12.
Australian channels 0, 4, 5 and 5A are outside the U.S VHF TV band so are not receivable. Although 5A (Newcastle)  is receivable here, I do not rely on it as it's merely a translator for Sydney Ch2. Channel 3, also from Newcastle is not worth watching as it's largely rebroadcasting Sydney's Ch9 which serves up American sitcoms and sport; both of which are a waste of transmitter power.

For Ch2, either American channel 3 is tuned up 3Mc/s or channel 4 is tuned down 3Mc/s.
For Ch3, American channel 6 is tuned up 3Mc/s.
For Ch7, American channel 8 is tuned up 1Mc/s.
For Ch9, American channel 10 is tuned down 3Mc/s or channel 11 is tuned up 4Mc/s.
For Ch10, American channel 12 is tuned up 4Mc/s or channel 13 is tuned down 2Mc/s.

Whether you tune up or down to get the channels depends on the range of adjustment. It is also preferable from the RF tracking point of view to use channels that require least adjustment. Needless to say, channel 7 works the best.  Modern solid state sets with a varicap tuner do not suffer this limitation of course and will get all the capital city VHF channels with no modification.
Lastly, the set was reassembled in its cabinet and the picture tube rotated to the correct position. Not an easy operation to do it in situ with the set on but my nimble fingers are used to doing things like that. Getting at the tube clamp that goes around the front of the CRT requires some dexterity. The other option of trial and error removing the chassis, rotating the tube, replacing it and seeing if it lines up seemed to tedious.
Final job was to fix the channel knob. I put a 9BA bolt through the knob so it matched up with the gap in the tuner shaft. No way can it slip on the shaft now.

My first commercially made electrostatic set is now up and running.

Summary.
The cheap '"let's see what we can get away with" factor is evident in this set. The poor vertical linearity may have escaped the non technical purchaser of this set, but the way the sync separator was, that could not be ignored. Maybe the original 6AU6 sync valve just so happened to have the right characteristics and the set did work ok when new. But if this was so, having a design that only works with selected valves is poor practice.
In any case, the sync separator was still not perfect after the modification.
The low RF gain I ended up with on Ch10 is admittedly my fault as I've forced the tuner to work 4Mc/s off frequency without having attended to the associated RF circuits. I would have preferred to use U.S Ch13 instead of 12 but there wasn't enough downward frequency adjustment.
Sound quality is actually very good. The video IF overloads on very strong signals which is hardly surprising given the simple AGC cannot throttle back the video IF gain enough. However, I do have strong signals from my aerial system and it isn't difficult to attenuate the signals if overload is evident. This is one limitation of simple AGC. However, it is important to remember that when this set was designed, AGC of any sort was new to the TV scene, as was intercarrier sound. The design of sync separation and electrostatic deflection circuits had been established since the mid 1930's, so I do feel the set should have performed better in these areas.
To sum up, the things which needed attention before this set was put into production are: 1)improved vertical linearity, 2)vertical blanking circuit required, 3)sync separator made immune to scene changes, 3)something better than a fluted shaft for the channel knob that can take the stress of turning the tight tuner shaft.
Performance is not as good as the Admiral 17T1 or my homemade 5BP1 set. However, it is a useable set despite the limitations and I'm fortunate to own this piece of television history.

Postscript.
With the end of analog TV transmissions in Australia as of December 2013, retuning the sound IF stages and tuners of system M television sets is a pointless excercise. It's less work, and in many cases the results will be better, to simply use an RF modulator for system M fed with the local 625 line 50 field video signal from a digital box, DVD player, etc. In effect, the set is fed with a system N signal (625 line 50 field but with 4.5Mc/s SIF and U.S. channel frequencies). Low cost VHF modulators for system M can be easily obtained from the U.S. ebay. It is of course possible to modify a system B modulator instead.

Home

email me: cablehack at yahoo dot com